Please check the box contents after unpacking. If any components are missing, please contact the dealer.
|E600Mini Integrated Smart Terminal||1|
|AC Power Adapter||1|
|SIM Card Ejector Tool||1|
|Printer Paper Roll||1|
|Multi-functional Base (optional)||1|
The following section points out the various hardware features and functions of the E600Mini.
The following section provides basic operating instructions for the E600Mini.
- Power ON: Press and hold the Power button for three seconds until the main screen displays normally.
- Power OFF: Press and hold the Power button for three seconds until the shutdown menu appears then tap “Shutdown”. The terminal will turn off after a few seconds.
Tear paper: Press the print paper downward along the cutter and tear it left or right when getting close to the main display.
Charge: Insert the external adapter or the base to charge the device. A red indicator light means the device is charging; green means charging is completed; the indicator flashing in red and green alternately means charging is abnormal.
Insert SIM/ microSD card: Insert the SIM Card Ejector Tool into the SIM / mircoSD card slot to open the tray and place the SIM card or microSD card on the tray. Gently insert it back into the terminal.
Connecting the Base:
- Use a network cable to connect the base’s LAN interface with a gateway device that can access the Internet, such as router, LAN switch.
- Place the host on the base.
- Insert the adapter 9V / 2A that comes with the terminal.
Base Usage Instruction
The base is mainly used for the host’s port expansion. Gently align and place the E600Mini terminal on the base. When the base’s network interface is connected, the E600Mini host will automatically switch the data
connection to the Ethernet connection on the base.
Note: When using the machine, do not shake or vibrate the base and E600Mini, so as to avoid the interruption of the data connection between the host and the base.
The E600Mini includes the following card readers:
NFC/Contactless Card Reader
Place the contactless card on the center of the payment module screen.
Magnetic Stripe Reader
Place the magnetic stripe face down (keep the magnetic stripe card perpendicular to the main display), swipe card through the magnetic card slot at a constant speed.
IC/Smart Card Reader
Place the IC chip face down, then insert the IC card into the card slot, and push it to the end.
CLEANING THE DEVICE
- Do not use industrial strength or abrasive cleaner as it may damage or scratch the screen.
- Do not immerse the device in water or liquid.
- Do not spray water or cleaner into ports.
- To clean the screen, apply distilled water or mild glass cleaner onto a soft, lint-free cloth and gently wipe terminal.
TERMINAL USAGE TIPS
- Avoid exposing the terminal in hot, humid, dusty or strong
- Do not violently vibrate, shake or beat the product.
- Do not plug/unplug any units of the product when it is power on, otherwise it may damage the internal circuit.
- Do not maintain the terminal if you are non-professional
- Before inserting the magnetic stripe/IC/contactless card,
please check whether there is any foreign object inside or
surround the card slot , and if any , report to related
Risk of explosion if battery replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Hereby, PAX Technology Limited. declares that the radio
equipment type E600M is in compliance with Directive
The full text of the EU declaration of conformity is available at
the following internet address：
For 5GHz WiFi version
FCC compliance statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. FCC SAR statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body ISED compliance statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) L’appareil ne doit pas produire de brouillage; (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans le même canal; IC SAR statement This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body. Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur. Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio établie par le développement énergétique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu’il est correctement porté sur le corps.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by PAX Technology, Inc. is under license. Other trademarks and trade names are those of their respective owners.
PAX Technology Inc reserves the right to change product technology specifications without notification.