CONTENTS CHECKLIST
Please check the box contents after unpacking. If any components are missing, please contact the dealer.
Name | Qty. |
A6650 Smart Handheld Computer | 1 |
AC Power Adapter | 1 |
Cable | 1 |
Hand Belt (optional) | 1 |
Product Description
Front & Back View:
Installation
SAM/SIM/Micro SD Card:
- Pull out the card slot on the left side of the terminal.
- Insert the SAM/SIM card to the corresponding card slot.
Instructions
Power On/Off
- Power On: Press the ON/OFF button for two seconds until the LCD backlight turns on.
- Power Off: Press the ON/OFF button for two seconds until the shutdown menu displays. Select “Power Off” to shut down the device.
Magnetic Stripe Card
Place the magnetic strip end of the magnetic card toward the device and swipe the card smoothly in the magnetic reader slot.
IC Card
Insert the chip side of the IC card into the IC card slot.
Contactless Card
Place the contactless card above the sensor area on the top of the A6650.
NFC
Place the NFC device/card above the sensor area on the battery cover.
General Usage Tips
- If any cables become damaged, seek a replacement.
- Do not insert unknown materials into any port on the A6650; this may cause serious damage.
- If repairs are required, please contact a professional technician instead of attempting them on your own.
- Avoid exposing the device to an excessively hot, dusty, or strong electromagnetic environment.
- Do not vibrate, shake, or drop the device.
Battery Usage Tips
- The device is equipped with a field replaceable battery. The product warranty is only valid if batteries supplied by PAX Technology are used.
- Do not expose the battery to direct sunlight or smoky/dusty environments.
- Do not strike, squeeze, or step on the battery.
- Do not place the battery into liquid or fire.
- Charging time should not exceed 24 hours. Over-charging or over-discharging may damage the battery.
- If the device is not being used for an extended period, whether in storage or otherwise, make sure to recharge the battery at least every 6 months.
- PAX Technology recommends replacing the battery every 2 years or after 500 recharge cycles.
- Dispose of batteries in a responsible manner.
Environmental Parameters
- Working Environment: Temperature: -10°C~50°C; Humidity range: 10%~93% (non-condensation)
- Storage Environment: Temperature: -20°C~70°C; Humidity range: 10%~93% (non-condensation)
Compliance Statements
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC SAR statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
ISED 5G Wi-Fi statement
The user manual for LE-LAN devices shall contain instructions related to the restrictions mentioned in the above sections, namely that:
i. the device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
ii. where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.
i. le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans le même canal;
ii. le cas échéant, le (s) type (s) d’antenne, le (s) modèle (s) d’antenne et l’angle (s) d’inclinaison le plus défavorable nécessaire (s) pour rester conforme (e) au p.e. L’exigence relative au masque d’élévation énoncée à la section 6.2.2.3 doit être clairement indiquée.
IC SAR statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur.
Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio établie par le développement énergétique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu’il est correctement porté sur le corps.