Q25 QUICK SETUP GUIDE

CONTENTS CHECKLIST

Please check the box contents after unpacking. If any components are missing, please contact the dealer.

NameQty.
Q25 POS Terminal1
Communication Cable1
AC Power Adapter1

PRODUCT DESCRIPTION

The following section points out the various hardware features of the Q25.

Front View:


 

BASIC OPERATING INSTRUCTIONS

The following section provides basic operating instructions for the Q25.

Power Connection

  1. Power can be supplied to the Q25 by connecting the AC power adapter to the communication cable, as in the case of RS232 or USB configurations, or via a powered USB cable (12V Powered USB) where the connected POS terminal provides the power.
  2. Power can also be supplied to the Q25 by connecting the AC power adapter to the Type-C USB port.

Please Note: To connect the communication cable to the device, remove the back cover and connect the communication cable head to the 2×7 pin interface.

Reset Device

The Q25 provides two reset options:

  1. When the application is down, press and hold the ‘X’ button for 3 seconds and then confirm on the LCD screen; the operating system and application will reset.
  2. When the operating system is down, please disconnect and reconnect the power cable to restart the device.

USB and PIN Pad Connection

The Q25’s 2×7 pin communication supports PIN Pad connection as well as USB data connection for downloading and debugging purposes. The 2×7 pin communication port is the default port for USB and PIN Pad connection.

SAM Installation

The Q25 has three SAM card slots. These card slots are normally hidden under the back cover. In order to install a SAM card into any of these slots, insert a card into the card slot with the contacts facing upwards and the clipped corner of the card facing forward and to the right.


CARD READERS

The Q25 includes the following card readers:

Magnetic Stripe Card 

Slide the card through the card reader slot from top to bottom or from bottom to top with the magnetic strip oriented towards the body of the device. Make sure that the card is fully inserted into the card reader while swiping the card.

IC/Smart Card Reader

Insert the card fully into the reader with the metallic contacts facing up and towards the device. Make sure that the card is fully inserted into the card reader while scanning the card.

Contactless Card Reader

The contactless card reader reads cards and devices placed roughly within an inch (2.5 mm). For best results, place as close to the reader as possible and center the card over the indicated area at the back of the terminal.


 

CLEANING THE DEVICE

  • Do not use industrial strength or abrasive cleaner as it may damage or scratch the screen.
  • Do not use industrial strength or abrasive cleaner.
  • Do not immerse the device in water or liquid.
  • Do not spray water or cleaner into EMV Card Reader or ports.

 

TERMINAL INSTALLATION AND USAGE TIPS

  • If any cables become damaged, seek a replacement.
  • Do not insert unknown materials into any port on the Q25; this may cause serious damage.
  • If repairs are required, please contact a professional technician instead of attempting them on your own.
  • Avoid exposing the device to an excessively hot, dusty, or strong electromagnetic environment.
  • Do not vibrate, shake, or drop the device.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.


For 5GHz WiFi version

FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

FCC SAR statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body
ISED compliance statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans le même canal;

IC SAR statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body.

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé. L’utilisateur final doit suivre les instructions spécifiques pour satisfaire les normes. Cet émetteur ne doit pas être co-implanté ou fonctionner en conjonction avec toute autre antenne ou transmetteur.
Le dispositif portatif est conçu pour répondre aux exigences d’exposition aux ondes radio établie par le développement énergétique DURABLE. Ces exigences un SAR limite de 1,6 W/kg en moyenne pour un gramme de tissu. La valeur SAR la plus élevée signalée en vertu de cette norme lors de la certification de produit à utiliser lorsqu’il est correctement porté sur le corps.